 |
| Sand and Gravel Processing |
Construction Sand and Gravel
Sand and gravel typically are mined in a moist or wet condition by open pit excavation or by dredging.
Open pit excavation is carried out with power shovels, draglines, front end loaders, and bucket wheel excavators. In rare situations, light charge blasting is done to loosen the deposit. Mining by dredging involves mounting the equipment on boats or barges and removing the sand and gravel from the bottom of the body of water by suction or bucket-type dredges. After mining, the materials are transported to the processing plant by suction pump, earth mover, barge, truck, belt conveyors, or other means.
Although significant amounts of sand and gravel are used for fill, bedding, subbase, and basecourse without processing, most domestic sand and gravel are processed prior to use. The processing of sand and gravel for a specific market involves the use of different combinations of washers, screens, and classifiers to segregate particle sizes; crushers to reduce oversized material; and storage and loading facilities.
After being transported to the processing plant, the wet sand and gravel raw feed is stockpiled or emptied directly into a hopper, which typically is covered with a "grizzly" of parallel bars to screen out large cobbles and boulders. From the hopper, the material is transported to fixed or vibrating scalping screens by gravity, belt conveyors, hydraulic pump, or bucket elevators. The scalping screens separate the oversize material from the smaller, marketable sizes. Oversize material may be used for erosion control, reclamation, or other uses, or it may be directed to a crusher for size reduction, to produce crushed aggregate, or to produce manufactured sands. Crushing generally is carried out in one or two stages, although three-stage crushing may also be performed. Following crushing, the material is returned to the screening operation for sizing.
The material that passes through the scalping screen is fed into a battery of sizing screens, which generally consists of either horizontal or sloped, and either single or multideck, vibrating
screens. Rotating trommel screens with water sprays are also used to process and wash wet sand and gravel. Screening separates the sand and gravel into different size ranges. Water is sprayed onto the material throughout the screening process. After screening, the sized gravel is transported to stockpiles, storage bins, or, in some cases, to crushers by belt conveyors, bucket elevators, or screw conveyors.
The sand is freed from clay and organic impurities by log washers or rotary scrubbers. After scrubbing, the sand typically is sized by water classification. Wet and dry screening is rarely used to size the sand. After classification, the sand is dewatered using screws, separatory cones, or hydroseparators. Material may also be rodmilled to produce smaller sized fractions, although this practice is not common in the industry. After processing, the sand is transported to storage bins or stockpiles by belt conveyors, bucket elevators, or screw conveyors.
Although significant amounts of sand and gravel are used for fill, bedding, subbase, and basecourse without processing, most domestic sand and gravel are processed prior to use. The processing of sand and gravel for a specific market involves the use of different combinations of washers, screens, and classifiers to segregate particle sizes; crushers to reduce oversized material; and storage and loading facilities.
After being transported to the processing plant, the wet sand and gravel raw feed is stockpiled or emptied directly into a hopper, which typically is covered with a "grizzly" of parallel bars to screen out large cobbles and boulders. From the hopper, the material is transported to fixed or vibrating scalping screens by gravity, belt conveyors, hydraulic pump, or bucket elevators. The scalping screens separate the oversize material from the smaller, marketable sizes. Oversize material may be used for erosion control, reclamation, or other uses, or it may be directed to a crusher for size reduction, to produce crushed aggregate, or to produce manufactured sands. Crushing generally is carried out in one or two stages, although three-stage crushing may also be performed. Following crushing, the material is returned to the screening operation for sizing.
The material that passes through the scalping screen is fed into a battery of sizing screens, which generally consists of either horizontal or sloped, and either single or multideck, vibrating
screens. Rotating trommel screens with water sprays are also used to process and wash wet sand and gravel. Screening separates the sand and gravel into different size ranges. Water is sprayed onto the material throughout the screening process. After screening, the sized gravel is transported to stockpiles, storage bins, or, in some cases, to crushers by belt conveyors, bucket elevators, or screw conveyors.
The sand is freed from clay and organic impurities by log washers or rotary scrubbers. After scrubbing, the sand typically is sized by water classification. Wet and dry screening is rarely used to size the sand. After classification, the sand is dewatered using screws, separatory cones, or hydroseparators. Material may also be rodmilled to produce smaller sized fractions, although this practice is not common in the industry. After processing, the sand is transported to storage bins or stockpiles by belt conveyors, bucket elevators, or screw conveyors.
Industrial Sand and Gravel
Industrial sand and gravel typically are mined from open pits of naturally occurring quartz-rich sand and sandstone.
Mining methods depend primarily on the degree of cementation of the rock. In some deposits, blasting is required to loosen the material prior to processing. The material may undergo primary crushing at the mine site before being transported to the processing plant.
The mined rock is transported to the processing site and stockpiled. The material then is crushed. Depending on the degree of cementation, several stages of crushing may be required to achieve the desired size reduction. Gyratory crushers, jaw crushers, roll crushers, and impact mills are used for primary and secondary crushing. After crushing, the size of the material is further reduced to 50 micrometers or smaller by grinding, using smooth rolls, media mills, autogenous mills, hammer mills, or jet mills. The ground material then is classified by wet screening, dry screening, or air classification. At some plants, after initial crushing and screening, a portion of the sand may be diverted to construction sand use.
After initial crushing and screening, industrial sand and gravel are washed to remove unwanted dust and debris and are then screened and classified again. The sand (now containing 25 to 30 percent moisture) or gravel then goes to an attrition scrubbing system that removes surface stains from the material by rubbing in an agitated, high-density pulp. The scrubbed sand or gravel is diluted with water to 25 to 30 percent solids and is pumped to a set of cyclones for further desliming. If the deslimed sand or gravel contains mica, feldspar, and iron bearing minerals, it enters a froth flotation process to which sodium silicate and sulfuric acid are added. The mixture then enters a series of spiral classifiers where the impurities are floated in a froth and diverted to waste. The purified sand, which has a moisture content of 15 to 25 percent, is conveyed to drainage bins where the moisture content is reduced to about 6 percent. The material is then dried in rotary or fluidized bed dryers to a moisture content of less than 0.5 percent. The dryers generally are fired with natural gas or oil, although other fuels such as propane or diesel also may be used. After drying, the material is cooled and then undergoes final screening and classification prior to being stored and packaged for shipment.
Process Systems & Design are experts in the processing of sand and gravel. Visit http://www.processsystemsdesign.com or call (410) 861-6437 with any inquiries or questions you may have.
The mined rock is transported to the processing site and stockpiled. The material then is crushed. Depending on the degree of cementation, several stages of crushing may be required to achieve the desired size reduction. Gyratory crushers, jaw crushers, roll crushers, and impact mills are used for primary and secondary crushing. After crushing, the size of the material is further reduced to 50 micrometers or smaller by grinding, using smooth rolls, media mills, autogenous mills, hammer mills, or jet mills. The ground material then is classified by wet screening, dry screening, or air classification. At some plants, after initial crushing and screening, a portion of the sand may be diverted to construction sand use.
After initial crushing and screening, industrial sand and gravel are washed to remove unwanted dust and debris and are then screened and classified again. The sand (now containing 25 to 30 percent moisture) or gravel then goes to an attrition scrubbing system that removes surface stains from the material by rubbing in an agitated, high-density pulp. The scrubbed sand or gravel is diluted with water to 25 to 30 percent solids and is pumped to a set of cyclones for further desliming. If the deslimed sand or gravel contains mica, feldspar, and iron bearing minerals, it enters a froth flotation process to which sodium silicate and sulfuric acid are added. The mixture then enters a series of spiral classifiers where the impurities are floated in a froth and diverted to waste. The purified sand, which has a moisture content of 15 to 25 percent, is conveyed to drainage bins where the moisture content is reduced to about 6 percent. The material is then dried in rotary or fluidized bed dryers to a moisture content of less than 0.5 percent. The dryers generally are fired with natural gas or oil, although other fuels such as propane or diesel also may be used. After drying, the material is cooled and then undergoes final screening and classification prior to being stored and packaged for shipment.
Process Systems & Design are experts in the processing of sand and gravel. Visit http://www.processsystemsdesign.com or call (410) 861-6437 with any inquiries or questions you may have.
